Stepper Control
Systems

Drive Box Specifications

Product
Description		 2 Amp
Half
Stepping
Drive Box		 3.5 Amp
Half
Stepping
Drive Box		 3.5 Amp
Micro
Stepping
Drive Box		 10 Amp
Micro
Stepping
Drive Box
Front Picture 2-3.5DriveBoxFront 2-3.5DriveBoxFront 2-3.5DriveBoxFront 2-3.5DriveBoxFront
Rear Picture 2-3.5DriveBoxBack 2-3.5DriveBoxBack 2-3.5DriveBoxBack 10ADriveBoxBack
Part # of Drive Box (X = # of axes) CP-X020H
add to quote 		CP-X035H
add to quote 		CP-X035M
add to quote 		CP-X100M
add to quote
Part # of Drive Box w/ Signal Generator CP-501A-
X020H
add to quote 		CP-501A-
X035H
add to quote 		CP-501A-
X035M
add to quote 		CP-501A-
X100M
add to quote
Replacement Drive Module OD-H-2A-
2035
add to quote 		OD-H-3.5A-
3535
add to quote 		OD-M-3.5A-
3540
add to quote 		OD-M-10A-
MBC10641
add to quote
Phase Current Range [A] 0.125 – 2.0 0.4 – 3.5 0.4 – 3.5 1.5 – 10.0
Bus Voltage [VDC] 32 32 32 80
Step Resolution Full,1/2 Full, 1/2 1/2, 1/5, 1/10, 1/64 Full, 1/2,
1/5, 1/8,
1/10, 1/16,
1/32, 1/64
Idle Current Reduction 50% 50% 50% 70%
Input Voltage [VAC] 110 or 220 110 or 220 110 or 220 110 or 220
Commonly Works With These Motors MP-2301, MP-2302 MP-2302, MP-3402, MP-3403 MP-2301, MP-2302, MP-3402, MP-3403 MP-3402, MP-3403, MP-4201
Weight [lbs] 10 10 10 20
Weight [kg] 4.5 4.5 4.5 9.1
Length [in] 7.5 7.5 7.5 14.75
Length [mm] 190.50 190.50 190.50 375.00
Width [in] 11.75 11.75 11.75 7
Width [mm] 298.50 298.50 298.50 178.00
Height [in] 4.5 4.5 4.5 6.5
Height [mm] 114.50 114.50 114.50 165.00
Corresponding Reference 2 – 3.5 Amp Stepper Drive Box Setup Manual 2 – 3.5 Amp Stepper Drive Box Setup Manual 2 – 3.5 Amp Stepper Drive Box Setup Manual 10 Amp Micro Stepping Drive Box Manual
Diagram 2-3.5DriveBoxModel 2-3.5DriveBoxModel 2-3.5DriveBoxModel 10DriveBoxModel
Signal Generator
PC Interface USB
Input Voltage 9VDC using 110 VAC or 220VAC Adapter (included)
Physical Size 8” x 6.25” x H=2.5"
203 x 159 x 63.5 mm
I/O Lines
(Standard)		 8 input, 8 output
I/O Lines
(with I/O Expansion Option)		 32 input, 32 output, 2 analog
Computer Requirements

Version 3

IBM compatible, Pentium 800MHz or Equivalent Processor
Windows NT/2000/XP/Vista
1-2 GB RAM depending on part complexity
1 Available USB or Serial Port (USB/Serial depends on signal generator)
Hard drive with at least 40MB of available space
High-performance graphics card*

*Recommended to improve performance when adjusting the viewports, but not required

 

Determining Your Drive Box Part Number

Flashcut CNC offers a wide variety of Stepper Motor Drivers. Use the following diagram to determine the part number for the driver that you need. Although there are many possible combinations, we have given a few examples below.

Part Number Diagram